Buffer amplifier
429442
212165866
2008-05-13T18:31:51Z
Mild Bill Hiccup
5202324
fixed link to remove redirection
A '''buffer amplifier''' (sometimes simply called a '''buffer''') is one that provides [[electrical impedance]] transformation from one circuit to another. Two main types of buffer exist: the '''voltage buffer''' and the '''current buffer'''.
[[Image:Ideal Buffers.png|thumbnail|200px|Figure 1: Top: Ideal voltage buffer Bottom: Ideal current buffer]]
==Voltage buffer==
Typically a voltage buffer amplifier is used to transfer a voltage from a first circuit, having a high [[output impedance]] level, to a second circuit with a low [[input impedance]] level. The interposed buffer amplifier prevents the second circuit from loading the first circuit unacceptably and interfering with its desired operation. In the ideal voltage buffer in the diagram, the input resistance is infinite, the output resistance zero (impedance of an ideal voltage source is zero). Other properties of the ideal buffer are: perfect linearity, regardless of signal amplitudes; and instant output response, regardless of the speed of the input signal.
If the voltage is transferred unchanged (the voltage [[gain]] ''A<sub>v</sub>'' is 1), the amplifier is a '''unity gain buffer'''; also known as a '''voltage follower''' because the output voltage ''follows'' or tracks the input voltage. Although the voltage gain of a voltage buffer amplifier may be (approximately) unity, it usually provides considerable current gain and thus power gain. However, it is commonplace to say that it has a gain of 1 (or the equivalent 0 [[decibel|dB]]), referring to the voltage gain.
As an example, consider a [[Thevenin's theorem|Thévenin source]] (voltage ''V<sub>A</sub>'', series resistance ''R<sub>A</sub>'') driving a resistor load ''R<sub>L</sub>''. Because of [[voltage division]] (also referred to as "loading") the voltage across the load is only ''V<sub>A</sub> R<sub>L</sub> / ( R<sub>L</sub> + R<sub>A</sub> )''. However, if the Thévenin source drives a unity gain buffer such as that in Figure 1 (top, with unity gain), the voltage input to the amplifier is ''V<sub>A</sub>'', with ''no voltage division'' because the amplifier input resistance is infinite. At the output the dependent voltage source delivers voltage ''A<sub>v</sub> V<sub>A</sub> = V<sub>A</sub>'' to the load, again without voltage division because the output resistance of the buffer is zero. A Thévenin equivalent circuit of the combined original Thévenin source ''and'' the buffer is an ideal voltage source ''V<sub>A</sub>'' with zero Thévenin resistance.
==Current buffer==
Typically a current buffer amplifier is used to transfer a current from a first circuit, having a low [[output impedance]] level, to a second circuit with a high [[input impedance]] level. The interposed buffer amplifier prevents the second circuit from loading the first circuit unacceptably and interfering with its desired operation. In the ideal current buffer in the diagram, the input resistance is zero, the output resistance infinite (impedance of an ideal current source is infinite). Again, other properties of the ideal buffer are: perfect linearity, regardless of signal amplitudes; and instant output response, regardless of the speed of the input signal.
For a current buffer, if the current is transferred unchanged (the current [[gain]] ''β<sub>i</sub>'' is 1), the amplifier is again a '''unity gain buffer'''; this time known as a '''current follower''' because the output current ''follows'' or tracks the input current.
As an example, consider a [[Norton's theorem|Norton source]] (current ''I<sub>A</sub>'', parallel resistance ''R<sub>A</sub>'') driving a resistor load ''R<sub>L</sub>''. Because of [[current division]] (also referred to as "loading") the current delivered to the load is only ''I<sub>A</sub> R<sub>A</sub> / ( R<sub>L</sub> + R<sub>A</sub> )''. However, if the Norton source drives a unity gain buffer such as that in Figure 1 (bottom, with unity gain), the current input to the amplifier is ''I<sub>A</sub>'', with ''no current division'' because the amplifier input resistance is zero. At the output the dependent current source delivers current ''β<sub>i</sub> I<sub>A</sub> = I<sub>A</sub>'' to the load, again without current division because the output resistance of the buffer is infinite. A Norton equivalent circuit of the combined original Norton source ''and'' the buffer is an ideal current source ''I<sub>A</sub>'' with infinite Norton resistance.
[[Image:Opampvoltagefollower.svg|thumb|Figure 2. Diagram of an [[op-amp]]–based unity gain buffer amplifier]]
==Voltage buffer examples==
=== Op-amps ===
A [[1 (number)|unity]] gain buffer amplifier may be constructed very simply by connecting the output of an [[operational amplifier]] to its inverting input ([[negative feedback]]), and connecting a signal source to the non-inverting input. For this circuit, V<sub>out</sub> is simply equal to V<sub>in</sub>.
The importance of this circuit does not come from any change in voltage, but from the input and output impedances of the op-amp. The input impedance of the op-amp is very high ([[Ohm|MΩ]] to 10 [[teraohm|TΩ]]), meaning that the input of the op-amp does not load down the source or draw any current from it. Because the output impedance of the op-amp is very low, it drives the load as if it were a perfect [[voltage source]]. Both the connections to and from the buffer are therefore [[impedance bridging|bridging]] connections, which reduce power consumption in the source, [[distortion]] from overloading, [[crosstalk]] and other [[electromagnetic interference]].
=== Single-transistor circuits ===
[[Image:Bipolar Voltage Follower.png|thumbnail|150px|Figure 3: Top: BJT voltage follower Bottom: Small-signal, low-frequency [[equivalent circuit]] using [[hybrid-pi model]]]]
[[Image:MOSFET Voltage Follower.png|thumbnail|150px|Figure 4: Top: MOSFET voltage follower Bottom: Small-signal, low-frequency [[equivalent circuit]] using [[hybrid-pi model]]]]
Other unity gain buffer amplifiers include the [[bipolar junction transistor]] in [[common collector|common-collector]] configuration (called an ''emitter follower'' because the emitter voltage follows the base voltage, or a ''voltage follower'' because the output voltage follows the input voltage); the [[MOSFET]] in [[common drain|common-drain]] configuration (called a ''source follower'' because the source voltage follows the gate voltage or, again, a ''voltage follower'' because the output voltage follows the input voltage); a pair of such transistors ([[Darlington pair]]); or similar configurations using [[field effect transistor]]s (a [[source follower]]), [[vacuum tube]]s ([[cathode follower]]), or other active devices. All such amplifiers actually have a gain of slightly less than unity, but the difference is usually small and unimportant.
=====Impedance transformation using the bipolar voltage follower=====
Using the small-signal circuit in Figure 3, the impedance seen looking into the circuit is
::<math> R_{in} = \frac {v_x} {i_x} = r_{\pi} + (\beta +1) (r_O//R_L) </math>.
(The analysis uses the relation ''g<sub>m</sub>r<sub>π</sub> = (I<sub>C</sub> /V<sub>T</sub>) (V<sub>T</sub> /I<sub>B</sub>)'' = β, which follows from the evaluation of these parameters in terms of the bias currents.) Assuming the usual case where ''r<sub>O</sub>'' >> ''R<sub>L</sub>'', the impedance is looking into the buffer is larger than the load ''R<sub>L</sub>'' without the buffer by a factor of (β +1), which is substantial because β is large. The impedance is increased even more by the added ''r<sub>π</sub>'', but often ''r<sub>π</sub>'' << (β +1) R<sub>L</sub>, so the addition does not make much difference.
=====Impedance transformation using the MOSFET voltage follower=====
Using the small-signal circuit in Figure 4, the impedance seen looking into the circuit is no longer ''R<sub>L</sub>'' but instead is infinite (at low frequencies) because the MOSFET draws no current.
As frequency is increased, the parasitic capacitances of the transistors come into play and the transformed input impedance drops with frequency.
=== Integrated buffer amplifiers ===
It is common for a single [[Dual in-line package|package]] to contain several discrete buffer amplifiers. For example, a '''hex buffer''' is a single package containing 6 discrete buffer amplifiers, and an '''octal buffer''' is a single package containing 8 discrete buffer amplifiers.
=== Speaker array amplifiers ===
The majority of amplifiers used to drive large speaker arrays, such as those used for rock concerts, are unity-gain, high-current amplifiers. Some current amplifiers take the voltage output from Class A/B, B, or tube (valve) amplifiers, while others contain built-in voltage amplifiers as a pre-amp stage. The result is a signal nearly identical to the input signal in terms of voltage, but capable of sending high amounts of current into low impedance speaker arrays where the speakers are wired in parallel.
==Current buffer examples==
Simple unity gain buffer amplifiers include the [[bipolar junction transistor]] in [[common base|common-base]] configuration, or the [[MOSFET]] in [[common gate|common-gate]] configuration (called a ''current follower'' because the output current follows the input current). The current gain of a current buffer amplifier is (approximately) unity.
=== Single-transistor circuits ===
[[Image:Bipolar current follower2.PNG|thumbnail|200px|Figure 5: Bipolar current follower biased by current source ''I<sub>E</sub>'' and with active load ''I<sub>C</sub>'' ]]
Figure 5 shows a bipolar current buffer biased with a current source (designated ''I<sub>E</sub>'' for DC emitter current) and driving another DC current source as active load (designated ''I<sub>C</sub>'' for DC collector current). The AC input signal current ''i<sub>in</sub>'' is applied to the emitter node of the transistor by an AC [[Norton's theorem|Norton current source]] with Norton resistance ''R<sub>S</sub>''. The AC output current ''i<sub>out</sub>'' is delivered by the buffer via a large coupling capacitor to load ''R<sub>L</sub>''. This coupling capacitor is large enough to be a short-circuit at frequencies of interest.
Because the transistor output resistance connects input and output sides of the circuit, there is a (very small) backward voltage feedback from the output to the input so this circuit is not unilateral. In addition, for the same reason, the input resistance depends (slightly) upon the output load resistance, and the output resistance depends significantly on the input driver resistance. For more detail see the article on [[common base|common base amplifier]].
== See also ==
* [[Preamplifier]]
* [[Common base]]
* [[Common gate]]
* [[Common collector]]
* [[Common drain]]
== External links ==
* [http://www.facstaff.bucknell.edu/mastascu/elessonshtml/OpAmps/OpAmp3Note1Buffer.html Unity Gain Buffer Amplifier — Bucknell]
[[Category:Electronic amplifiers]]
[[bg:Буферен усилвател]]
[[de:Mikrofonverstärker]]
[[it:Amplificatore separatore]]
[[pt:Buffer (Eletrônica)]]
[[ru:Буферный усилитель]]