Negative feedback amplifier 181384 223119290 2008-07-02T17:35:24Z 125.20.65.74 /* Voltage amplifiers */ When a fraction of the output of an amplifier is combined with the input, feedback exists; if the feedback opposes the original signal, it is '''negative feedback''' and if it increases the signal it is '''positive feedback'''. A '''negative feedback amplifier''', or more commonly simply a '''feedback amplifier''', is an [[amplifier]] which uses negative feedback to improve performance (gain stability, linearity, frequency response, [[step response]]) and reduce sensitivity to parameter variations due to manufacturing or environmental uncertainties. A single feedback loop with unilateral blocks is shown in Figure 1. Negative feedback is used in this way in many amplifiers and control systems.<ref name=Kuo> {{cite book |author=Kuo, Benjamin C & Farid Golnaraghi |title=Automatic control systems |edition=Eighth edition |page=p. 46 |year= 2003 |publisher=Wiley |location=NY |isbn=0471134767 |url=http://worldcat.org/isbn/0471134767}} </ref> [[Image:Block diagram for feedback.PNG|thumb|Figure 1: Ideal negative feedback model|300px|right]] == Overview == Fundamentally, all electronic devices used to provide power gain (e.g. [[vacuum tube]]s, [[BJT|bipolar transistors]], [[FET|MOS transistors]]) are [[nonlinear]]. Negative feedback allows gain to be traded for higher linearity (reducing [[distortion]]), amongst other things. If not designed correctly amplifiers with negative feedback can become unstable, resulting in unwanted behavior, such as [[oscillation]]. The [[Nyquist stability criterion]] developed by [[Harry Nyquist]] of [[Bell Laboratories]] can be used to study the stability of feedback amplifiers. Feedback amplifiers share these properties:<ref name=Palumbo> {{cite book |author=Palumbo, Gaetano & Salvatore Pennisi |title=Feedback amplifiers: theory and design |page=p. 64 |year= 2002 |publisher=Kluwer Academic |location=Boston/Dordrecht/London |isbn=0792376439 |url=http://worldcat.org/isbn/0792376439}} </ref> Pros: *Can increase or decrease input impedance (depending on type of feedback) *Can increase or decrease output impedance (depending on type of feedback) *Reduces distortion (increases linearity) *Increases the bandwidth *Desensitizes gain to component variations *Can control [[step response]] of amplifier Cons: *May lead to instability if not designed carefully *The gain of the amplifier decreases *The input and output impedances of the amplifier with feedback (the '''closed-loop amplifier''') become sensitive to the gain of the amplifier without feedback (the '''open-loop amplifier'''); that exposes these impedances to variations in the open loop gain, for example, due to parameter variations or due to nonlinearity of the open-loop gain ==History== The negative feedback amplifier was invented by [[Harold Stephen Black]] (US patent 2,102,671 (issued in 1937)<ref>{{cite web | title=http://eepatents.com/patents/2102671.pdf | url=http://eepatents.com/patents/2102671.pdf | accessdate = 2005-10-24}}</ref> ) while a passenger on the Lackawanna Ferry (from Hoboken Terminal to Manhattan) on his way to work at [[Bell Laboratories]] (historically located in Manhattan instead of New Jersey in 1927) on [[August 2]], [[1927]]. Black had been toiling at reducing [[distortion]] in [[repeater]] amplifiers used for telephone transmission. On a blank space in his copy of The New York Times,<ref> Currently on display at Bell Laboratories in Mountainside, New Jersey</ref> he recorded the diagram found in Figure 1, and the equations derived below.<ref name=Waldhauer> {{cite book |author=Waldhauer, Fred |title=Feedback |page=p. 3 |year= 1982 |publisher=Wiley |location=NY |isbn=0471053198 |url=http://worldcat.org/isbn/0471053198}} </ref> ==Classical feedback== === Voltage amplifiers === Below, the gain of the amplifier with feedback, the '''closed-loop gain''' ''A''<sub>fb</sub>, is derived in terms of the gain of the amplifier without feedback, the '''open-loop gain''' ''A''<sub>OL</sub> and the '''feedback factor''' β, which governs how much of the output signal is applied to the input. See Figure 1, top right. The feedback parameter β is determined by the feedback network that is connected around the amplifier. For an [[operational amplifier]] two resistors may be used for the feedback network to set β between 0 and 1. This network may be modified using reactive elements like [[capacitor]]s or [[inductor]]s to (a) give frequency-dependent closed-loop gain as in equalization/tone-control circuits or (b) construct oscillators. Consider a voltage amplifier with voltage feedback. Without feedback, the output voltage ''V''<sub>out</sub> = A''<sub>OL</sub> ''V''<sub>in</sub>, where the open-loop gain ''A''<sub>OL</sub>'' in general may be a function of both frequency and voltage. The open-loop gain ''A''<sub>OL</sub> is defined by: :<math>A_\mathrm{OL} = \frac{V_\mathrm{out}}{V_\mathrm{in}} \ ,</math> where ''V<sub>in</sub>'' is the input to the amplifier, assuming no feedback, and ''V<sub>out</sub>'' is the amplifier output, again with no feedback. Suppose we have a feedback loop so that a fraction β V<sub>out</sub> of the output is subtracted from the input. The input to the amplifier is now ''V’<sub>in</sub>'', where :<math>V'_\mathrm{in} = V_\mathrm{in} - \beta \cdot V_\mathrm{out}</math> The gain of the amplifier with feedback, called the closed-loop gain, ''A<sub>fb</sub>'' is given by, :<math>A_\mathrm{fb} = \frac{V_\mathrm{out}}{V_\mathrm{in}}</math> Substituting for ''V<sub>in</sub>'', :<math>A_\mathrm{fb} = \frac{V_\mathrm{out}}{V'_\mathrm{in} + \beta \cdot V_\mathrm{out}}</math> Dividing numerator and denominator by ''V’<sub>in</sub>'', :<math>A_\mathrm{fb} = \frac{ \frac{V_\mathrm{out}}{V'_\mathrm{in}} }{ 1 + \beta \cdot \frac{V_\mathrm{out}}{V'_\mathrm{in}} }</math> But since :<math>A_\mathrm{fb} = \frac{V_\mathrm{out}}{V'_\mathrm{in}}</math>, then :<math>A_\mathrm{OL} = \frac{A_\mathrm{fb}}{1 + \beta \cdot A_\mathrm{fb}}</math> If ''A''<sub>OL</sub> >> 1, then ''A''<sub>fb</sub> ≈ 1 / β and the effective amplification (or closed-loop gain) ''A''<sub>fb</sub> is set by the feedback constant β, and hence set by the feedback network, usually a simple reproducible network, thus making linearizing and stabilizing the amplification characteristics straightforward. Note also that if there are conditions where β ''A''<sub>OL</sub> = −1, the amplifier has infinite amplification – it has become an oscillator, and the system is unstable. The stability characteristics of the gain feedback product β ''A''<sub>OL</sub> are often displayed and investigated on a [[Nyquist plot]] (a polar plot of the gain/phase shift as a parametric function of frequency). A simpler, but less general technique, uses [[Bode plot#Gain margin and phase margin|Bode plot]]s. The combination ''L'' = β ''A''<sub>OL</sub> appears commonly in feedback analysis and is called the '''loop gain'''. The combination ( 1 + β ''A''<sub>OL</sub> ) also appears commonly and is variously named as the '''desensitivity factor''' or the '''improvement factor'''. ===Bandwidth extension=== [[Image:Bandwidth comparison.JPG|thumb|380px|Figure 2: Gain vs. frequency for a single-pole amplifier with and without feedback; corner frequencies are labeled.]] Feedback can be used to extend the bandwidth of an amplifier (speed it up) at the cost of lowering the amplifier gain.<ref>[http://bwrc.eecs.berkeley.edu/classes/ee140/Lectures/10_stability.pdf RW Brodersen ''Analog circuit design: lectures on stability'' ] </ref> Figure 2 shows such a comparison. The figure is understood as follows. Without feedback the so-called '''open-loop''' gain in this example has a single time constant frequency response given by ::<math> A_{OL}(f) = \frac {A_0} { 1+ j f / f_C } \ , </math> where ''f<sub>C</sub>'' is the [[cutoff frequency|cutoff]] or [[corner frequency]] of the amplifier: in this example ''f<sub>C</sub>'' = 10<sup>4</sup> Hz and the gain at zero frequency A<sub>0</sub> = 10<sup>5</sup> V/V. The figure shows the gain is flat out to the corner frequency and then drops. When feedback is present the so-called '''closed-loop''' gain, as shown in the formula of the previous section, becomes, ::<math> A_{fb} (f) = \frac { A_{OL} } { 1 + \beta A_{OL} } </math> ::::<math> = \frac { A_0/(1+jf/f_C) } { 1 + \beta A_0/(1+jf/f_C) } </math> ::::<math> = \frac {A_0} {1+ jf/f_C + \beta A_0} </math> ::::<math> = \frac {A_0} {(1 + \beta A_0) \left(1+j \frac {f} {(1+ \beta A_0) f_C } \right)} \ . </math> The last expression shows the feedback amplifier still has a single time constant behavior, but the corner frequency is now increased by the improvement factor ( 1 + β A<sub>0</sub> ), and the gain at zero frequency has dropped by exactly the same factor. This behavior is called the '''[[gain-bandwidth product|gain-bandwidth tradeoff]]'''. In Figure 2, ( 1 + β A<sub>0</sub> ) = 10<sup>3</sup>, so ''A<sub>fb</sub>''(0)= 10<sup>5</sup> / 10<sup>3</sup> = 100 V/V, and ''f<sub>C</sub>'' increases to 10<sup>4</sup> × 10<sup>3</sup> = 10<sup>7</sup> Hz. ===Multiple poles=== When the open-loop gain has several poles, rather than the single pole of the above example, feedback can result in complex poles (real and imaginary parts). In a two-pole case, the result is peaking in the frequency response of the feedback amplifier near its corner frequency, and ringing and overshoot in its [[step response]]. In the case of more than two poles, the feedback amplifier can become unstable, and oscillate. See the discussion of [[Bode plot#Gain margin and phase margin|gain margin and phase margin]]. For a complete discussion, see Sansen.<ref name=Sansen> {{cite book |author=Willy M. C. Sansen |title=Analog design essentials |year= 2006 |pages=§0513-§0533, p. 155-165 |publisher=Springer |location=New York; Berlin |isbn=0-387-25746-2 |url=http://worldcat.org/isbn/0-387-25746-2}} </ref> ==Asymptotic gain model== {{main|asymptotic gain model}} In the above analysis the feedback network is [[Electronic amplifier#Unilateral or bilateral|unilateral]]. However, real feedback networks often exhibit '''feed forward''' as well, that is, they feed a small portion of the input to the output, degrading performance of the feedback amplifier. A more general way to model negative feedback amplifiers including this effect is with the [[asymptotic gain model]]. ==Feedback and amplifier type== Amplifiers use current or voltage as input and output, so four types of amplifier are possible. See [[Electronic amplifier#Input and output variables|classification of amplifiers]]. Any of these four choices may be the open-loop amplifier used to construct the feedback amplifier. The objective for the feedback amplifier also may be any one of the four types of amplifier, not necessarily the same type as the open-loop amplifier. For example, an op amp (voltage amplifier) can be arranged to make a current amplifier instead. The conversion from one type to another is implemented using different feedback connections, usually referred to as series or shunt (parallel) connections.<ref>[http://www.ece.mtu.edu/faculty/goel/EE-4232/Feedback.pdf Ashok K. Goel ''Feedback topologies'']</ref><ref> [http://centrevirtuel.creea.u-bordeaux.fr/ELAB/docs/freebooks.php/virtual/feedback-amplifier/textbook_feedback.html#1.2 Zimmer T & Geoffreoy D: ''Feedback amplifier''] </ref> See the table below. {| class="wikitable" style="background:white;text-align:center " !Feedback amplifier type !Input connection !Output connection !Ideal feedback !Two-port feedback |- |-valign="top" | '''Current''' | '''Shunt''' | '''Series''' | '''CCCS''' | '''g-parameter''' |- |-valign="top" | '''Transresistance''' | '''Shunt''' | '''Shunt''' | '''VCCS''' | '''y-parameter''' |- |-valign="top" | '''Transconductance''' | '''Series''' | '''Series | '''CCVS''' | '''z-parameter''' |- |-valign="top" | '''Voltage''' | '''Series''' | '''Shunt''' | '''VCVS''' | '''h-parameter''' |} The feedback can be implemented using a [[two-port network]]. There are four types of two-port network, and the selection depends upon the type of feedback. For example, for a current feedback amplifier, current at the output is sampled and combined with current at the input. Therefore, the feedback ideally is performed using an (output) current-controlled current source (CCCS), and its imperfect realization using a two-port network also must incorporate a CCCS, that is, the appropriate choice for feedback network is a g-parameter two-port. ==Two-port analysis of feedback== One approach to feedback is the use of [[return ratio]]. Here an alternative method used in most textbooks<ref>[http://organics.eecs.berkeley.edu/~viveks/ee140/lectures/section10p4.pdf Vivek Subramanian: ''Lectures on feedback'' ]</ref><ref name=Gray-Meyer1> {{cite book |author=P R Gray, P J Hurst, S H Lewis, and R G Meyer |title=Analysis and Design of Analog Integrated Circuits |year= 2001 |page=pp. 586-587 |edition=Fourth Edition |publisher=Wiley |location=New York |isbn=0-471-32168-0 |url=http://worldcat.org/isbn/0471321680}}</ref><ref name=Sedra1> {{cite book |author=A. S. Sedra and K.C. Smith |title=Microelectronic Circuits |year= 2004 |edition=Fifth Edition |pages=Example 8.4, pp. 825-829 and PSpice simulation pp. 855-859 |publisher=Oxford |location=New York |isbn=0-19-514251-9 |url=http://worldcat.org/isbn/0-19-514251-9}} </ref> is presented by means of an example treated in the article on [[Asymptotic gain model#Two-stage transistor amplifier|asymptotic gain model]]. [[Image:Two-transistor feedback amp.PNG|thumbnail|250px|Figure 3: A ''shunt-series'' feedback amplifier]] Figure 3 shows a two-transistor amplifier with a feedback resistor ''R<sub>f</sub>''. The aim is to analyze this circuit to find three items: the gain, the output impedance looking into the amplifier from the load, and the input impedance looking into the amplifier from the source. ===Replacement of the feedback network with a two-port=== The first step is replacement of the feedback network by a two port. Just what components go into the two port? On the input side of the two-port we have ''R<sub>f</sub>''. If the voltage at the right side of ''R<sub>f</sub>'' changes, it changes the current in ''R<sub>f</sub>'' that is subtracted from the current entering the base of the input transistor. That is, the input side of the two-port is a dependent current source controlled by the voltage at the top of resistor ''R<sub>2</sub>''. One might say the second stage of the amplifier is just a [[voltage follower]], transmitting the voltage at the collector of the input transistor to the top of ''R<sub>2</sub>''. That is, the monitored output signal is really the voltage at the collector of the input transistor. That view is legitimate, but then the voltage follower stage becomes part of the feedback network. That makes analysis of feedback more complicated. [[Image:G-equivalent circuit.PNG|thumbnail|250px|Figure 4: The g-parameter feedback network]] An alternative view is that the voltage at the top of ''R<sub>2</sub>'' is set by the emitter current of the output transistor. That view leads to an entirely passive feedback network made up of ''R<sub>2</sub>'' and ''R<sub>f</sub>''. The variable controlling the feedback is the emitter current, so the feedback is a current-controlled current source (CCCS). We search through the four available [[two-port network]]s and find the only one with a CCCS is the g-parameter two-port, shown in Figure 4. The next task is to select the g-parameters so that the two-port of Figure 4 is electrically equivalent to the L-section made up of ''R<sub>2</sub>'' and ''R<sub>f</sub>''. That selection is an algebraic procedure made most simply by looking at two individual cases: the case with ''V<sub>1</sub>'' = 0, which makes the VCVS on the right side of the two-port a short-circuit; and the case with ''I<sub>2</sub>'' = 0. which makes the CCCS on the left side an open circuit. The algebra in these two cases is simple, much easier than solving for all variables at once. The choice of g-parameters that make the two-port and the L-section behave the same way are shown in the table below. {| class="wikitable" style="background:white;text-align:center " !g<sub>11</sub> !g<sub>12</sub> !g<sub>21</sub> !g<sub>22</sub> |- |-valign="center" | '''<math>\frac {1} {R_f+R_2}</math>''' | '''<math> - \frac {R_2}{R_2+R_f}</math>'' | '''<math> \frac {R_2} {R_2+R_f} </math>''' | '''<math>R_2//R_f \ </math>''' |} [[Image:Small-signal current amplifier with feedback.PNG|thumbnail|400px|Figure 5: Small-signal circuit with two-port for feedback network; upper shaded box: main amplifier; lower shaded box: feedback two-port replacing the ''L''-section made up of ''R''<sub>f</sub> and ''R''<sub>2</sub>.]] ===Small-signal circuit=== The next step is to draw the small-signal schematic for the amplifier with the two-port in place using the [[hybrid-pi model]] for the transistors. Figure 5 shows the schematic with notation ''R<sub>3</sub>'' = ''R<sub>C2</sub> // R<sub>L</sub>'' and ''R<sub>11</sub>'' = 1 / ''g<sub>11</sub>'', ''R<sub>22</sub>'' = ''g<sub>22</sub>'' . ===Loaded open-loop gain=== Figure 3 indicates the output node, but not the choice of output variable. A useful choice is the short-circuit current output of the amplifier (leading to the short-circuit current gain). Because this variable leads simply to any of the other choices (for example, load voltage or load current), the short-circuit current gain is found below. First the loaded '''open-loop gain''' is found. The feedback is turned off by setting ''g<sub>12</sub> = g<sub>21</sub>'' = 0. The idea is to find how much the amplifier gain is changed because of the resistors in the feedback network by themselves, with the feedback turned off. This calculation is pretty easy because ''R<sub>11</sub>, R<sub>B</sub>, and r<sub>π1</sub>'' all are in parallel and ''v<sub>1</sub> = v<sub>π</sub>''. Let ''R<sub>1</sub>'' = ''R<sub>11</sub> // R<sub>B</sub> // r<sub>π1</sub>''. In addition, ''i<sub>2</sub> = −(β+1) i<sub>B</sub>''. The result for the open-loop current gain ''A<sub>OL</sub>'' is: ::<math> A_{OL} = \frac { \beta i_B } {i_S} = g_m R_C \left( \frac { \beta }{ \beta +1} \right) \left( \frac {R_1} {R_{22} + \frac {r_{ \pi 2} + R_C } {\beta + 1 } } \right) \ . </math> ===Gain with feedback=== In the classical approach to feedback, the feedforward represented by the VCVS (that is, ''g<sub>21</sub> v<sub>1</sub>'') is neglected.<ref>If the feedforward is included, its effect is to cause a modification of the open-loop gain, normally so small compared to the open-loop gain itself that it can be dropped. Notice also that the main amplifier block is [[Electronic amplifier#Unilateral or bilateral|unilateral]].</ref> That makes the circuit of Figure 5 resemble the block diagram of Figure 1, and the gain with feedback is then: ::<math> A_{FB} = \frac { A_{OL} } {1 + { \beta }_{FB} A_{OL} } </math> :::<math> = \frac {A_{OL} } {1 + \frac {R_2} {R_2+R_f} A_{OL} } \ , </math> where the feedback factor β<sub>FB</sub> = −g<sub>12</sub>. Notation β<sub>FB</sub> is introduced for the feedback factor to distinguish it from the transistor β. ===Input and output resistances=== [[Image:Feedback amplifier input resistance.PNG|thumb|500px|Figure 6: Circuit set-up for finding feedback amplifier input resistance]] First, a digression on how two-port theory approaches resistance determination, and then its application to the amplifier at hand. ====Background on resistance determination==== Figure 6 shows a test circuit for finding the input resistance of a feedback voltage amplifier (left) and for a feedback current amplifier (right). In the case of the voltage amplifier [[Kirchhoff's circuit laws|Kirchhoff's voltage law]] provides: ::<math> V_x = I_x R_{in} + \beta v_{out} \ , </math> where ''v''<sub>out</sub> = ''A''<sub>v</sub> ''v''<sub>in</sub> = ''A''<sub>v</sub> ''I''<sub>x</sub> ''R''<sub>in</sub>. Substituting this result in the above equation and solving for the input resistance of the feedback amplifier, the result is: ::<math> R_{in}(fb) = \frac {V_x} {I_x} = \left( 1 + \beta A_v \right ) R_{in} \ . </math> The general conclusion to be drawn from this example and a similar example for the output resistance case is: ''A series feedback connection at the input (output) increase the input (output) resistance by a factor ( 1 + β ''A''<sub>OL</sub> )'', where ''A''<sub>OL</sub> = open loop gain. On the other hand, for the current amplifier, which uses a shunt input connection, Kirchhoff's laws provide: ::<math> I_x = \frac {V_{in}} {R_{in}} + \beta i_{out} \ . </math> where ''i''<sub>out</sub> = ''A''<sub>i</sub> ''i''<sub>in</sub> = ''A''<sub>i</sub> ''V''<sub>x</sub> / ''R''<sub>in</sub>. Substituting this result in the above equation and solving for the input resistance of the feedback amplifier, the result is: ::<math> R_{in}(fb) = \frac {V_x} {I_x} = \frac { R_{in} } { \left( 1 + \beta A_i \right ) } \ . </math> The general conclusion to be drawn from this example and a similar example for the output resistance case is: ''A parallel feedback connection at the input (output) decreases the input (output) resistance by a factor ( 1 + β ''A''<sub>OL</sub> )'', where ''A''<sub>OL</sub> = open loop gain. These conclusions can be generalized to treat cases with arbitrary [[Norton's theorem|Norton]] or [[Thevenin's theorem|Thévenin]] drives, arbitrary loads, and general [[two-port network|two-port feedback networks]]. However, the results do depend upon the main amplifier having a representation as a two-port – that is, the results depend on the ''same'' current entering and leaving the input terminals, and likewise, the same current that leaves one output terminal must enter the other output terminal. A broader conclusion to be drawn, independent of the quantitative details, is that feedback can be used to increase or to decrease the input and output impedances. ====Application to the example amplifier==== These resistance results now are applied to the amplifier of Figure 3 and Figure 5. The ''improvement factor'' that reduces the gain, namely ( 1 + β<sub>FB</sub> A<sub>OL</sub>), directly decides the effect of feedback upon the input and output resistances of the amplifier. In the case of a shunt connection, the input impedance is reduced by this factor; and in the case of series connection, the impedance is multiplied by this factor. However, the impedance that is modified by feedback is the impedance of the amplifier in Figure 5 with the feedback turned off, and does include the modifications to impedance caused by the resistors of the feedback network. Therefore, the input impedance seen by the source with feedback turned off is ''R''<sub>in</sub> = ''R''<sub>1</sub> = ''R''<sub>11</sub> // ''R''<sub>B</sub> // ''r''<sub>π1</sub>, and with the feedback turned on (but no feedforward) ::<math> R_{in} = \frac {R_1} {1 + { \beta }_{FB} A_{OL} } \ , </math> where ''division'' is used because the input connection is ''shunt'': the feedback two-port is in parallel with the signal source at the input side of the amplifier. A reminder: ''A''<sub>OL</sub> is the ''loaded'' open loop gain [[Negative feedback amplifier#Loaded open-loop gain|found above]], as modified by the resistors of the feedback network. The impedance seen by the load needs further discussion. The load in Figure 5 is connected to the collector of the output transistor, and therefore is separated from the body of the amplifier by the infinite impedance of the output current source. Therefore, feedback has no effect on the output impedance, which remains simply ''R<sub>C2</sub>'' as seen by the load resistor ''R<sub>L</sub>'' in Figure 3.<ref>The use of the improvement factor ( 1 + β<sub>FB</sub> A<sub>OL</sub>) requires care, particularly for the case of output impedance using series feedback. See Jaeger, note below.</ref><ref name=Jaeger> {{cite book | title = Microelectronic Circuit Design | author =R.C. Jaeger and T.N. Blalock | publisher = McGraw-Hill Professional | year = 2006 |edition=Third Edition |page=Example 17.3 pp. 1092-1096| isbn = 978-0-07-319163-8 | url = http://worldcat.org/isbn/978-0-07-319163-8 }}</ref> If instead we wanted to find the impedance presented at the ''emitter'' of the output transistor (instead of its collector), which is series connected to the feedback network, feedback would increase this resistance by the improvement factor ( 1 + β<sub>FB</sub> A<sub>OL</sub>).<ref>That is, the impedance found by turning off the signal source ''I<sub>S</sub>'' = 0, inserting a test current in the emitter lead ''I<sub>x</sub>'', finding the voltage across the test source ''V<sub>x</sub>'', and finding ''R<sub>out</sub> = V<sub>x</sub> / I<sub>x</sub>''.</ref> ===Load voltage and load current=== The gain derived above is the current gain at the collector of the output transistor. To relate this gain to the gain when voltage is the output of the amplifier, notice that the output voltage at the load ''R<sub>L</sub>'' is related to the collector current by [[Ohm's law]] as ''v<sub>L</sub> = i<sub>C</sub> (R<sub>C2</sub> // R<sub>L</sub>)''. Consequently, the transresistance gain ''v<sub>L</sub> / i<sub>S</sub>'' is found by multiplying the current gain by ''R<sub>C2</sub> // R<sub>L</sub>'': ::<math> \frac {v_L} {i_S} = A_{FB} (R_{C2}//R_L ) \ . </math> Similarly, if the output of the amplifier is taken to be the current in the load resistor ''R<sub>L</sub>'', [[current division]] determines the load current, and the gain is then: ::<math> \frac {i_L} {i_S} = A_{FB} \frac {R_{C2}} {R_{C2} + R_L} \ . </math> === Is the main amplifier block a two port? === [[Image:Two-port ground arrangement.PNG|thumbnail|400px|Figure 7: Amplifier with ground connections labeled by ''G''. The feedback network satisfies the port conditions.]] Some complications follow, intended for the attentive reader. Figure 7 shows the small-signal schematic with the main amplifier and the feedback two-port in shaded boxes. The two-port satisfies the [[Two-port network|port conditions]]: at the input port, ''I''<sub>in</sub> enters and leaves the port, and likewise at the output, ''I''<sub>out</sub> enters and leaves. The main amplifier is shown in the upper shaded box. The ground connections are labeled. Figure 7 shows the interesting fact that the main amplifier does not satisfy the port conditions at its input and output unless the ground connections are chosen to make that happen. For example, on the input side, the current entering the main amplifier is ''I''<sub>S</sub>. This current is divided three ways: to the feedback network, to the bias resistor ''R''<sub>B</sub> and to the base resistance of the input transistor ''r''<sub>π</sub>. To satisfy the port condition for the main amplifier, all three components must be returned to the input side of the main amplifier, which means all the ground leads labeled ''G''<sub>1</sub> must be connected, as well as emitter lead ''G''<sub>E1</sub>. Likewise, on the output side, all ground connections ''G''<sub>2</sub> must be connected and also ground connection ''G''<sub>E2</sub>. Then, at the bottom of the schematic, underneath the feedback two-port and outside the amplifier blocks, ''G''<sub>1</sub> is connected to ''G''<sub>2</sub>. That forces the ground currents to divide between the input and output sides as planned. Notice that this connection arrangement ''splits the emitter'' of the input transistor into a base-side and a collector-side – a physically impossible thing to do, but electrically the circuit sees all the ground connections as one node, so this fiction is permitted. Of course, the way the ground leads are connected makes no difference to the amplifier (they are all one node), but it makes a difference to the port conditions. That is a weakness of this approach: the port conditions are needed to justify the method, but the circuit really is unaffected by how currents are traded among ground connections. However, if there is '''no possible arrangement''' of ground conditions that will lead to the port conditions, the circuit might not behave the same way.<ref>The equivalence of the main amplifier block to a two-port network guarantees that performance factors work, but without that equivalence they may work anyway. For example, in some cases the circuit can be shown to be equivalent to another circuit that is a two port, by "cooking up" different circuit parameters that are functions of the original ones. There is no end to creativity!</ref> The improvement factors ( 1 + β<sub>FB</sub> A<sub>OL</sub>) for determining input and output impedance might not work. This situation is awkward, because a failure to make a two-port may reflect a real problem (it just is not possible), or reflect a lack of imagination (for example, just did not think of splitting the emitter node in two). As a consequence, when the port conditions are in doubt, at least two approaches are possible to establish whether improvement factors are accurate: either simulate an example using [[SPICE|Spice]] and compare results with use of an improvement factor, or calculate the impedance using a test source and compare results. A more radical choice is to drop the two-port approach altogether, and use [[return ratio]]s. That choice might be advisable if small-signal device models are complex, or are not available (for example, the devices are known only numerically, perhaps from measurement or from [[SPICE]] simulations). ==See also== * [[Operational amplifier]] * [[Phase margin]] * [[Bode plot]] * [[Asymptotic gain model]] * [[Frequency compensation]] * [[Pole splitting]] * [[Return ratio]] == References and notes == <references /> [[Category:Electronic feedback]] [[Category:Electronic amplifiers]]