Parts of a sail 1137758 207158670 2008-04-21T17:33:58Z JBazuzi 3144056 /* The corners */ propose merging [[earing]] [[Image:Parts of a sail.svg|right|thumb|Diagram of a triangular sail.]] In [[sailing]] the '''parts of a [[sail]]''' have common terminology. Most sails are now triangular; for such sails, there are six separate terms, one for each [[corner]] and edge. ==The corners== {{mergefrom|Earing|Talk:Parts of a sail#Merger proposal|date=April 2008}} [[Image:Mainsail-corners.png|left|thumb|The corners of a quadrilateral fore-and-aft sail.]] In a triangular sail, the upper point is known as the '''head'''; the [[halyard]], the [[rope|line]] which raises the sail, is attached to the head. The lower two points of the sail, on either end of the '''foot''' (the bottom edge of the sail), are called the '''[[Tack (sailing)|tack]]''' (forward) and '''clew''' (aft). The tack is shackled to a fixed point on the boat, such as the [[gooseneck]] in the case of a [[mainsail]], or the deck at the base of a stay, in the case of a [[jib]] or [[staysail]]. The clew is movable and is positioned with [[running rigging]]. A symmetrical sail may be said to have two clews. === Clew === The clew of a jib or other [[headsail]] is the free corner (not attached to any [[standing rigging]]), to which port and starboard jib [[sheet (sailing)|sheets]] are attached to control the angle of the sail to the wind. In a sail with a [[Boom (sailing)|boom]] (such as a mainsail on a [[sloop]]), the clew is attached to the boom, and can often be tightened along the boom using the [[outhaul]] to adjust the sail shape. On a [[square rig|square sail]] or a symmetrical [[spinnaker]], each of the lower corners is a clew, but the corner to which the sheet (the ''working sheet'' or ''leeward sheet'') is currently attached is called ''the clew''. Related terms are the 'clew lines', ropes attached to the clews, and 'clewgarnets' or 'cluegarnets', which are the [[block and tackle|tackles]] attached to clew lines. These lines and tackles are used to ‘clew up’ the ‘[[Course (sail)|courses]]’ (ie to pull the clews up onto the [[yard (sailing)|upper yard]] or the [[mast]] in preparation for [[furl (sailing)|furling]] the sail). ==The edges==<!-- This section is linked from [[Windsurfing]] --> [[Image:Mainsail-edges.png|right|thumb|The edges of a quadrilateral fore-and-aft sail.]] The '''foot''' of a sail is its lowest edge, bounded by the clew and the tack, or on some sails by the two clews. The forward (leading) edge of the sail is called the '''luff'''. This is related to the term ''luffing'', which is a condition where the sail ripples because wind is crossing over the front and back side simultaneously, caused when the angle of the wind fails to allow the sail to maintain a good aerodynamic shape; this condition usually starts near the luff as the boat passes through being [[close-hauled]]. A [[Cunningham (sailing)|cunningham]] may be rigged on the luff of the mainsail to help control the sail shape. The aft edge of a sail is called the '''leech'''. If incorrectly tensioned, the leech of a sail may "flutter" noisily; some larger mainsails are provided with a line which runs along a pocket in the leech, called a ''leech line'', for the purpose of tightening the leech to prevent this fluttering. ===The roach=== The shape of a sail is seldom a perfect triangle. It is common for sailmakers to add an arc of extra material on the leech, outside a line drawn from the head to the clew. This additional part of the sail is known as the '''roach'''; mainsails usually have roaches, but they are very occasionally found on specialized jibs as well. They provide additional power for a given mast/boom size. Since it cannot be supported by tension in the sail material (applied from the corners), it would flap uselessly unless some other provision were made for it. It is therefore supported by [[battens]], held in ''batten pockets'', which extend into the main portion of the sail. ==Non-triangular fore and aft sails== [[Gaff rig|Gaff]], [[gunter]], [[Lugger#Types of lugsail|lug]], [[Junk Rig|junk]] and some [[spritsail|sprit]] sails have four sides but are set fore and aft so that one edge is leading. That is, the '''luff'''. '''tack''', '''foot''', '''clew''' and '''leech''' are the same as for the triangular Bermuda sail. But the high aft corner is the '''peak''' and the top edge is the '''head'''. The corner between the head and the luff is the '''throat'''. === Square Sails === Although most sails used today are triangular and follow the conventions above, square sails are still used on a few vessels. Many of the same names are used for parts of a square sail. [[Image:Parts_of_a_square_sail.png|left|thumb|The parts of a square sail.]] ; Head : As for a triangular sail, this refers to the topmost part. On a square sail, however, this part is an edge rather than a corner. ; Leech : The "side" edge of the sail. Since square sails are symmetrical, they have two leeches. Occasionally, when the ship is [[close-hauled]], the windward edge of the sail might be referred to as the luff. ; Clew : Like a triangular sail, the "free" corners of a square sail are called clews; again there are two of them. Square sails have [[sheet (sailing)|sheet]]s attached to their clews like triangular sails, but the sheets are used to pull the sail down to the yard below rather than to adjust the angle it makes with the wind. ; Foot : The bottom edge of the sail. Square sails also have [[tack (square sail)|tack]]s and sheets, although they are not a part of the sail itself .... ==See also== * [[Glossary of nautical terms]] {{Sail Types}} [[Category:sailing vessels and rigging]] [[ru:Устройство паруса]] [[sv:Horn (seglingsterm)]]