Plastic welding 845000 222544483 2008-06-29T22:29:24Z Moggie2002 2199029 Fix typo and remove link spam. {{Cleanup|date=May 2007}} '''Plastic Welding''' is the process of [[welding]] [[plastic]] parts together. There are several techniques: ==Hot gas welding== This is a plastic welding technique which is analogous to [[gas welding]] of metals, though the specific techniques are different. A specially designed heat gun (hot air welder) produces a jet of hot air that softens the parts to be joined, as well as a plastic filler rod. Hot air/gas welding is a common fabrication technique for manufacturing smaller items such as chemical tanks, water tanks (black, grey, fresh & ballast), heat exchangers, and plumbing fittings. The materials being welded and the welding rod must be of the same or very similar plastic. Welding PVC to acrylic is an exception to this rule. -[http://www.seelyeinc-orl.com Seelye, Inc.]is one of the leading manufacturers of hot air/gas thermoplastic welders. Other manufacturers include [http://www.kamweld.com KAMWELD], [http://www.plasticweldingtools.com Malcom, Inc.], Leister,STAMMECH. Projects made from poly family plastics end up being cabinets, medical facility chases, transport assemblies among others. ==Free hand welding== With free hand welding, the jet of hot air from the welder is played on the weld area and the tip of the weld rod at the same time. As the rod softens, it is pushed into the joint and fuses to the parts. Free hand welding is a difficult technique to master, and is slow. However, welds can be made in almost any situation. ==Speed tip welding== With speed welding, the plastic welder, similar to a soldering iron in appearance and wattage, is fitted with a feed tube for the plastic weld rod. The speed tip heats the rod and the substrate, while at the same time it presses the molten weld rod into position. A bead of softened plastic is laid into the joint, and the parts and weld rod fuse. With some types of plastic such as polypropylene, the melted welding rod must be "mixed" with the semi-melted base material being fabricated or repaired. These welding techniques have been perfected over time and have been utilised for over 50 years by professional plastic fabricators and repairers internationally. Speed tip welding method is a much faster welding technique and with practice can be used in tight corners. == Plastic welding rod == This is the extruded rod that is used to weld plastic. Suitable rod materials include ABS, PVC, Polypropylene, polyethylene, and many other types of thermoplastic. Plastic welding rod is available in a wide range of colors to match a project's color. ==Extrusion welding== Extrusion welding allows the application of bigger welds in a single weld pass. It is the preferred technique for joining material over 6 mm thick. Welding rod is drawn into a miniature hand held plastic extruder, plasticized, and forced out of the extruder against the parts being joined, which are softened with a jet of hot air to allow bonding to take place. ==Contact welding== This is the same as [[spot welding]] except that heat is supplied with convection of the pincher tips instead of electrical conduction. Two plastic parts are brought together where heated tips pinch them, melting and joining the parts in the process. ==Hot plate welding== Related to contact welding, this technique is used to weld larger parts, or parts that have a complex weld joint geometry. The two parts to be welded are placed in the tooling attached to the two opposing platens of a press. A hot plate, with a shape that matches the weld joint geometry of the parts to be welded, is moved in position between the two parts. The two opposing platens move the parts into contact with the hot plate until the heat softens the interfaces to the melting point of the plastic. When this condition is achieved the hot plate is removed, and the parts are pressed together and held until the weld joint cools and re solidifies to create a permanent bond. ==High frequency welding== Certain plastics with chemical dipoles, such as polyvinyl chloride (PVC), polyamides (PA) and acetates can be heated with high frequency electromagnetic waves. High frequency welding uses this property to soften the plastics for joining. The heating can be localized, and the process can be continuous. Also known as Dielectric Sealing, R.F. (Radio Frequency) Heat Sealing. This is the same concept as [[induction welding]]. ==Ultrasonic welding== In [[ultrasonic welding]], high frequency (15 kHz to 40 kHz ) low amplitude vibration is used to create heat by way of friction between the materials to be joined. The interface of the two parts is specially designed to concentrate the energy for the maximum weld strength. ==Vibration or friction welding== In vibration or friction welding, the two parts to be assembled are rubbed together at a lower frequency (typically 100-300 Hz) and higher amplitude (typically 1-2 mm) than [[ultrasonic welding]]. The friction caused by the [[vibration]] motion combined with the clamping pressure between the two parts creates the heat to melt the contact interface between the two parts, and results in a strong weld. At the completion of the vibration motion the parts remain held together until the weld joint cools and the melted plastic re solidifies. The friction movement can be linear or orbital, and the joint design of the two parts has to allow this movement. ==Spin welding== Spin welding is another form of frictional welding. With this process, one part is held stationary, while the other one is rotated at high velocity. The rotating part is then pressed against the fixed part with significant force. This welding process is related to Vibration Welding. ==Laser welding== This technique requires one part to be transmissive to a laser beam and either the other part absorptive or a coating at the interface to be absorptive to the beam. The two parts are put under pressure while the laser beam moves along the joining line. The beam passes through the first part and is absorbed by the other one or the coating to generate enough heat to soften the interface creating a permanent weld. Semiconductor diode lasers are typically used in plastic welding. Wavelengths in the range of 808nm to 980nm can be used to join various plastic material combinations. Power levels from less than 1W to 100W are needed depending on the materials, thickness and desired process speed. <ref>{{cite web|title=Plastic Welding with Diode Lasers|url= http://www.coherent.com/Downloads/Laser_Spot_Welding_PlasticRev2.pdf}} www.coherent.com</ref> Diode laser systems have the following advantages in joining of plastic materials: • Cleaner than adhesive bonding • No micro-nozzles to get clogged • No liquid or fumes to affect surface finish • No consumables • Higher throughput • Can access work-piece in challenging geometry • High level of process control Requirements for high strength joints include: • Adequate transmission through upper layer • Absorption by lower layer • Material compatibility – wetting • Good joint design – clamping pressure, joint area • Lower power density Materials that can be joined include: • Polypropylene • Polycarbonate • Acrylic • Nylon • ABS Specific applications include sealing / welding / joining of: catheter bags, medical containers, automobile remote control keys, heart pacemaker casings, syringe tamper evident joints, headlight or tail-light assemblies, pump housings, and cellular phone parts. ==Solvent welding== In solvent welding, a solvent is applied which can temporarily dissolve the polymer at room temperature. When this occurs, the polymer chains are free to move in the liquid and can entangle with other similarly dissolved chains in the other component. Given sufficient time, the solvent will permeate through the polymer and out into the environment, so that the chains lose their mobility. This leaves a solid mass of entangled polymer chains which constitutes a solvent weld. ==Additional techniques== Hot air cold staking, Ultrasonic staking, Ultrasonic spot welding, Infra-red welding, Torsional welding == See also == * [[Plastic cement]] = References = {{reflist}} [[Category:Welding]] [[Category:Plastic welding]]