Raman spectroscopy
68686
223030365
2008-07-02T07:16:12Z
Jmameren
4632991
added closing parenthesis
'''Raman spectroscopy''' is a [[Spectroscopy|spectroscopic]] technique used in [[condensed matter physics]] and [[chemistry]] to study vibrational, rotational, and other low-frequency modes in a system.<ref name="Gardiner">{{cite book| last = Gardiner| first = D.J.| authorlink = | title = Practical Raman spectroscopy| publisher = [[Springer-Verlag]]| series = | year = 1989| doi = | isbn = 978-0387502540}}</ref> It relies on [[elastic scattering|inelastic]] scattering, or [[Raman scattering]] of monochromatic light, usually from a [[laser]] in the [[visible]], [[infrared|near infrared]], or [[ultraviolet|near ultraviolet]] range. The laser light interacts with [[phonon]]s or other excitations in the system, resulting in the energy of the laser photons being shifted up or down. The shift in energy gives information about the phonon modes in the system. [[Infrared spectroscopy]] yields similar, but complementary information.
Typically, a sample is illuminated with a laser beam. Light from the illuminated spot is collected with a [[lens (optics)|lens]] and sent through a [[monochromator]]. Wavelengths close to the laser line, due to elastic [[Rayleigh scattering]], are filtered out while the rest of the collected light is dispersed onto a detector.
Spontaneous [[Raman scattering]] is typically very weak, and as a result the main difficulty of Raman spectroscopy is separating the weak inelastically scattered light from the intense Rayleigh scattered laser light. Historically Raman [[spectrometer]]s used holographic [[diffraction grating]]s and multiple dispersion stages to achieve a high degree of laser rejection. In the past, [[Photomultiplier| PMTs]] were the detectors of choice for dispersive Raman setups, which resulted in long acquisition times. However, modern instrumentation almost universally employs notch or edge filters for laser rejection and spectrographs (either Czerny-Turner, echelle or FT based) and [[Charge-coupled device|CCD]] detectors.
There are a number of advanced types of Raman spectroscopy, including Surface enhanced Raman, polarised Raman, stimulated Raman (analogous to [[stimulated emission]]), Transmission Raman, Spatially offset Raman and Hyper Raman.
== Basic theory ==
[[Image:Raman energy levels.jpg|400px|thumb|Energy level diagram showing the states involved in Raman signal. The line thickness is roughly proportional to the signal strength from the different transitions.]]
The Raman effect occurs when light impinges upon a [[molecule]] and interacts with the electron cloud of the bonds of that molecule. The incident [[photon]] excites one of the electrons into a virtual state. For the spontaneous Raman effect, the molecule will be excited from the ground state to a virtual energy state, and relax into a vibrational excited state, which generates Stokes Raman scattering. If the molecule was already in an elevated vibrational energy state, the Raman scattering is then called anti-Stokes Raman scattering.
A molecular polarizability change, or amount of deformation of the electron cloud, with respect to the [[molecular vibration|vibrational coordinate]] is required for the molecule to exhibit the Raman effect. The amount of the polarizability change will determine the Raman scattering intensity, whereas the Raman shift is equal to the vibrational level that is involved.
[[image:CVRaman.jpg|left|thumb|200px|Sir Chandrasekhara V. Raman]]
== History ==
Although the inelastic scattering of light was predicted by Smekal in 1923, it was not until 1928 that it was observed in practice. The Raman effect was named after one of its discoverers, the Indian scientist [[Chandrasekhara Venkata Raman|Sir C. V. Raman]] who observed the effect by means of sunlight (1928, together with K. S. Krishnan and independently by [[Grigory Landsberg]] and [[Leonid Isaakovich Mandelstam|Leonid Mandelstam]]).<ref name="Gardiner" /> Raman won the [[Nobel Prize in Physics]] in 1930 for this discovery accomplished using sunlight, a narrow band photographic filter to create monochromatic light and a "crossed" filter to block this monochromatic light. He found that light of changed frequency passed through the "crossed" filter.
Subsequently the mercury arc became the principal light source, first with photographic detection and then with spectrophotometric detection. Currently [[laser]]s are used as light sources.
== Applications ==
Raman spectroscopy is commonly used in chemistry, since vibrational information is very specific for the chemical bonds in molecules. It therefore provides a fingerprint by which the molecule can be identified. The fingerprint region of organic molecules is in the range 500-2000 cm<sup>-1</sup>. Another way that the technique is used is to study changes in chemical bonding, e.g., when a substrate is added to an enzyme.
Raman gas analyzers have many practical applications. For instance, they are used in medicine for real-time monitoring of anaesthetic and respiratory gas mixtures during surgery.
In solid state physics, spontaneous Raman spectroscopy is used to, among other things, characterize materials, measure [[temperature]], and find the crystallographic orientation of a sample.
As with single molecules, a given solid material has characteristic [[phonon]] modes that can help an experimenter identify it. In addition, Raman spectroscopy can be used to observe other low frequency excitations of the solid, such as [[plasmon]]s, magnons, and [[BCS theory|superconducting gap]] excitations.
The spontaneous Raman signal gives information on the population of a given phonon mode in the ratio between the Stokes (downshifted) intensity and anti-Stokes (upshifted) intensity.
Raman scattering by an anisotropic [[crystal]] gives information on the crystal orientation. The [[polarization]] of the Raman scattered light with respect to the crystal and the polarization of the laser light can be used to find the orientation of the crystal, if the [[crystal structure]] (specifically, its [[crystallographic point group|point group]]) is known.
Raman active fibers, such as aramid and carbon, have vibrational modes that show a shift in Raman frequency with applied stress. Polypropylene fibers also exhibit similar shifts.
The radial breathing mode is a commonly used technique to evaluate the diameter of carbon nanotubes.
Spatially Offset Raman Spectroscopy (SORS), which is less sensitive to surface layers than conventional Raman, can be used to discover [[counterfeit drugs]] without opening their internal packaging, and for non-invasive monitoring of biological tissue.<ref>[http://news.bbc.co.uk/2/hi/health/6314287.stm BBC News report on use of Raman spectroscopy to detect fake drugs (31st January 2007).]</ref><ref>[http://www.cclrc.ac.uk/PMC/PRel/Arch/CCLRC/2007/20070129.aspx Science and Technology Facilities Council article.]</ref>
Raman spectroscopy can be used to investigate the chemical composition of historical documents such as the [[Book of Kells]] and contribute to knowledge of the social and economic conditions at the time the documents were produced. <ref>[http://www.nytimes.com/2007/05/28/world/europe/28kells.html Irish Classic Is Still a Hit (in Calfskin, Not Paperback) - New York Times<!-- Bot generated title -->]</ref> This is especially helpful because Raman spectroscopy offers a non-invasive way to determine the best course of [[Preservation (library and archival science)|preservation]] or [[art conservation|conservation]] treatment for such materials.
==Raman microspectroscopy==
Raman spectroscopy offers several advantages for [[microscopy|microscopic]] analysis. Since it is a scattering technique, specimens do not need to be fixed or sectioned. Raman spectra can be collected from a very small volume (< 1 µm in diameter); these spectra allow the identification of species present in that volume. Water does not interfere very strongly. Thus, Raman spectroscopy is suitable for the microscopic examination of [[mineral]]s, materials such as polymers and ceramics, [[cell (biology)|cell]]s and [[proteins]]. A Raman microscope begins with a standard optical microscope, and adds an excitation laser, a [[monochromator]], and a sensitive detector (such as a [[charge-coupled device]] (CCD), or [[photomultiplier]] tube (PMT)). [[Fourier transform spectroscopy|FT-Raman]] has also been used with microscopes.
In ''direct imaging'', the whole field of view is examined for scattering over a small range of wavenumbers (Raman shifts). For instance, a wavenumber characteristic for cholesterol could be used to record the distribution of cholesterol within a cell culture.
The other approach is ''[[hyperspectral imaging]]'' or ''[[chemical imaging]]'', in which thousands of Raman spectra are acquired from all over the field of view. The data can then be used to generate images showing the location and amount of different components. Taking the cell culture example, a hyperspectral image could show the distribution of cholesterol, as well as proteins, nucleic acids, and fatty acids. Sophisticated signal- and image-processing techniques can be used to ignore the presence of water, culture media, buffers, and other interferents.
Raman microscopy, and in particular [[confocal microscopy|confocal]] microscopy, has very high spatial resolution. For example, the lateral and depth resolutions were 250 nm and 1.7 µm, respectively, using a confocal Raman microspectrometer with the 632.8 nm line from a He-Ne [[laser]] with a pinhole of 100 µm diameter.
Since the objective lenses of microscopes focus the laser beam to several micrometres in diameter, the resulting photon flux is much higher than achieved in conventional Raman setups. This has the added benefit of enhanced [[fluorescence quenching]]. However, the high photon flux can also cause sample degradation, and for this reason some setups require a thermally conducting substrate (which acts as a heat sink) in order to mitigate this process.
By using Raman microspectroscopy, ''in vivo'' time- and space-resolved Raman spectra of microscopic regions of samples can be measured. As a result, the [[fluorescence]] of water, media, and buffers can be removed. Consequently ''in vivo'' time- and space-resolved Raman spectroscopy is suitable to examine [[proteins]], [[cell (biology)|cell]]s and [[organ (anatomy)|organs]].
Raman microscopy for biological and medical specimens generally uses [[near-infrared]] (NIR) lasers (785 nm diodes and 1064 nm Nd:YAG are especially common). This reduces the risk of damaging the specimen by applying high power. However, the intensity of NIR Raman is low (owing to the ω<sup>-4</sup> dependence of Raman scattering intensity), and most detectors required very long collection times. Recently, more sensitive detectors have become available, making the technique better suited to general use. Raman microscopy of inorganic specimens, such as rocks and ceramics and polymers, can use a broader range of excitation wavelengths.<ref>Ellis, D.I. and Goodacre, R. (2006) Metabolic fingerprinting in disease diagnosis: biomedical applications of infrared and Raman spectroscopy, Analyst, 131, 875-885. {{doi|10.1039/b602376m}}</ref>
==Polarized Raman Analysis==
The [[polarization]] of the Raman scattered light also contains useful information. This property can be measured using (plane) polarized laser excitation and a [[polarizer | polarization analyzer]]. Spectra acquired with the analyzer set at both perpendicular and parallel to the excitation plane can be used to calculate the [[depolarization ratio]]. Study of the technique is pedagogically useful in teaching the connections between [[group theory]], symmetry, Raman activity and peaks in the corresponding Raman spectra.
The spectral information arising from this analysis gives insight into molecular orientation and vibrational symmetry. In essence, it allows the user to obtain valuable information relating to the molecular shape, for example in synthetic chemistry or polymorph analysis. It is often used to understand macromolecular orientation in crystal lattices, [[liquid crystal]]s or polymer samples{{Fact|date=June 2008}}.
==Variations==
Several variations of Raman spectroscopy have been developed. The usual purpose is to enhance the sensitivity (e.g., surface-enhanced Raman), to improve the spatial resolution (Raman microscopy), or to acquire very specific information (resonance Raman).
* '''[[Surface Enhanced Raman Spectroscopy]] (SERS)''' - Normally done in a silver or gold colloid or a substrate containing silver or gold. Surface [[plasmons]] of silver and gold are excited by the laser, resulting in an increase in the electric fields surrounding the metal. Given that Raman intensities are proportional to the electric field, there is large increase in the measured signal (by up to 10<sup>11</sup>). This effect was originally observed by Fleishman but the prevailing explanation was proposed by Van Duyne in 1977.<ref>{{cite journal |last = Jeanmaire | first = David L. | coauthors = [[Richard P. van Duyne]] | title = Surface Raman Electrochemistry Part I. Heterocyclic, Aromatic and Aliphatic Amines Adsorbed on the Anodized Silver Electrode |journal = Journal of Electroanalytical Chemistry | volume = 84 | pages =1–20 | publisher = Elsevier Sequouia S.A. | date = 1977 | doi = 10.1016/S0022-0728(77)80224-6 }} </ref>
* '''Hyper Raman''' - A [[non-linear optics|non-linear]] effect in which the vibrational modes interact with the [[second harmonic generation|second harmonic]] of the excitation beam. This requires very high power, but allows the observation of vibrational modes which are normally "silent". It frequently relies on SERS-type enhancement to boost the sensitivity. <!-- Ref: K. Kneipp et al., Chem. Phys. 247 (1999) 155-162 -->
* '''[[Resonance Raman spectroscopy]]''' - The excitation wavelength is matched to an electronic transition of the molecule or crystal, so that vibrational modes associated with the excited electronic state are greatly enhanced. This is useful for studying large molecules such as [[polypeptide]]s, which might show hundreds of bands in "conventional" Raman spectra. It is also useful for associating normal modes with their observed frequency shifts.
* '''Spontaneous Raman Spectroscopy''' - Used to study the temperature dependence of the Raman spectra of molecules.
* '''Optical Tweezers Raman Spectroscopy (OTRS)''' - Used to study individual particles, and even biochemical processes in single cells trapped by [[optical tweezers]].
* '''Stimulated Raman Spectroscopy''' - A two color pulse transfers the population from ground to a rovibrationally excited state, if the difference in energy corresponds to an allowed Raman transition. Two photon UV ionization, applied after the population transfer but before relaxation, allows the intra-molecular or inter-molecular Raman spectrum of a gas or molecular cluster (indeed, a given conformation of molecular cluster) to be collected. This is a useful molecular dynamics technique.
* '''Spatially Offset Raman Spectroscopy (SORS)''' - The Raman scatter is collected from regions laterally offset away from the excitation laser spot, leading to significantly lower contributions from the surface layer than with traditional Raman spectroscopy.<ref> P. Matousek, I.P. Clark, E.R.C. Draper, M.D. Morris, A.E. Goodship, N. Everall, M. Towrie, W.F. Finney, A.W. Parker, Subsurface Probing in Diffusely Scattering Media using Spatially Offset Raman Spectroscopy, Appl. Spectrosc. 59 (2005) 393.</ref>
*'''[[Coherent anti-Stokes Raman spectroscopy]] (CARS)''' - Two laser beams are used to generate a coherent anti-Stokes frequency beam, which can be enhanced by resonance.
==References==
<references/>
==External links==
*[http://www.andor.com/chemistry/?app=64 Raman Fundamentals 'What is Raman Spectroscopy?']
*[http://www.piacton.com/Spectroscopy/raman.aspx Raman Spectroscopy application notes]
*[http://www.jobinyvon.com/default.asp?DocID=1070 Raman Resource Pages] - Tutorial, FAQs and application notes on various uses for Raman spectroscopy
*[http://www.doitpoms.ac.uk/tlplib/raman/index.php DoITPoMS Teaching and Learning Package - Raman Spectroscopy] - an introduction, aimed at undergraduate level
*[http://www.deltanu.com/dn06/tutorials.htm Raman Spectroscopy Tutorials] - An introductory tutorial
*[http://www.kosi.com/raman/resources/tutorial/ Raman Spectroscopy Tutorial] - A detailed explanation of Raman Spectroscopy including Resonance-Enhanced Raman Scattering and Surface-Enhanced Raman Scattering.
*[http://www.scienceofspectroscopy.info/edit/index.php?title=Raman_Spectroscopy Raman Spectroscopy] at The Science of Spectroscopy wiki supported by NASA.
* [http://www.abc.net.au/rn/science/ss/stories/s1581469.htm The Science Show, ABC Radio National] - Interview with Scientist on NASA funded project to build Raman Spectrometer for 2009 Mars mission: a cellular phone size device to detect almost any substance known, with commercial <USD$5000 commercial spin-off, prototyped by June 2006.
*[http://pubs.acs.org/subscribe/journals/ancham/79/i11/pdf/0607feature_griffiths.pdf Raman spectroscopy for medical diagnosis] from [http://pubs3.acs.org/acs/journals/toc.page?incoden=ancham&indecade=0&involume=79&inissue=11 the June 1, 2007 issue of ''Analytical Chemistry'']
*[http://www.scientistlive.com/lab/?/Chromatography/2007/12/10/19577/Raman_spectroscopy/ Raman Spectroscopy overview]
{{BranchesofSpectroscopy}}
[[Category:Spectroscopy]]
[[el:Φασματοσκοπία Ράμαν]]
[[de:Raman-Spektroskopie]]
[[fr:Spectroscopie Raman]]
[[nl:Ramanspectroscopie]]
[[pl:Spektroskopia Ramana]]