Regenerative circuit 343276 215927134 2008-05-30T09:15:47Z 68.148.164.166 /* The superheterodyne receiver */ [[Image:S7300059.JPG|250px|thumb|Homebuilt regenerative radio set with vintage headphones.]] [[Image:S7300056.JPG|250px|thumb|Rear view of the above radio, showing the simplicity of the regenerative design.]] {{otheruses |Heat exchanger#Regenerative heat exchanger}} The '''regenerative circuit''' (or '''self-regenerative circuit''') allows an electronic signal to be amplified many times by the same [[vacuum tube]] or other [[Electrical element|active component]] such as a [[field effect transistor]]. ==Description== [[Image:Regenerative Receiver.png|246px|thumb|right|Regenerative Receiver Schematic]] ''Regenerative circuits'' were employed in early radio receivers and are still built by electronics experimenters and students. A regenerative circuit is often an [[amplitude modulation|AM]] detector, converting the [[radio frequency|RF signal]] on the [[Antenna (radio)|antenna]] to an [[audio]] waveform. Their use of [[positive feedback]] greatly increases both the [[Electronic selectivity|selectivity]] and sensitivity of a simple receiver. Positive feedback builds up the input signal to very high levels. For AM signals, the detector is kept operating just below RF [[oscillation]]. For [[Single sideband modulation|single sideband]] and the unmodulated [[Radio frequency|RF]] used in [[Morse code|code]] reception, the circuit is operated at a level above oscillation to provide the necessary "beat note" ([[heterodyne]]), as these two transmission modes require a local oscillation to be understood. Although [[vacuum tube]]s were used on the early designs, modern [[transistor]]s (bipolar, JFET etc.) are often used today. Typical regenerative [[gain]]s for these devices are: bipolar transistor, 100,000; JFET 20,000, and vacuum tube: a few thousand. This is quite dramatic considering the fact that the non regenerative gain of these devices (at RF frequencies) is very low (often 20 or less). In addition to increasing gain, regeneration also greatly improves selectivity (simply stated the ability to separate stations on a crowded band). A final, often overlooked benefit is that regenerative radios, like their tuned-radio-frequency cousins, tend to provide very high quality, low distortion audio. With a hi-fi shortwave broadcast, their sound quality can be quite impressive. Regenerative circuits use fewer components than more complex designs and because of this the regeneration level must be carefully adjusted by the user. In the early vacuum tube designs, the tube detector could easily operate as a transmitter, at power levels as high as one [[watt (unit)|watt]]. So, it often caused [[RFI|interference]] to nearby receivers. Modern circuits, using [[semiconductor]]s normally operate at milliwatt levels, one thousand times lower. So, interference is far less of a problem today. In any case, the addition of a [[preamp]] stage (RF stage) between the regenerative detector and the antenna is often used to further lower the interference. Two common shortcomings of regenerative receivers are the presence of a charactertistic noise (“mush”) in their audio output, and sensitive and unstable tuning . Both of these problems have the same cause: a regenerative receiver’s gain is greatest when it operates on the verge of oscillation, and in that condition, the circuit behaves [[chaos theory|chaotically]].<ref>Domine M.W. Leenaerts and Wim M.G. van Bokhoven, “Amplification via chaos in regenerative detectors,” ''Proceedings of SPIE'' *, vol. 2612**, pages 136-145 (December 1995). (* SPIE = Society of Photo-optical Instrumentation Engineers; renamed: International Society for Optical Engineering) (** Jaafar M.H. Elmirghani, ed., ''Chaotic Circuits for Communication'' -- a collection of papers presented at the SPIE conference of 23-24 October 1995 in Philadelphia, Pennsylvania.)</ref><ref>Domine M.W. Leenaerts, “Chaotic behavior in superregenerative detectors,” ''IEEE Transactions on Circuits and Systems Part 1: Fundamental Theory and Applications'', vol. 43, no. 3 pages 169-176 (March 1996).</ref> ==History== The inventor of [[FM]] radio, [[Edwin Armstrong]], invented and patented the regenerative circuit while he was a junior in college, in 1914. He patented the super-regenerative circuit in 1922, and the [[superheterodyne]] receiver in1918). [[Lee De Forest]] filed a patent in [[1916]] that became the cause of a contentious lawsuit with the prolific inventor Armstrong, whose patent for the regenerative circuit had been issued in [[1914]]. The lawsuit lasted twelve years, winding its way through the appeals process and ending up at the [[Supreme Court of the United States|Supreme Court]]. The Court ruled in favor of De Forest, although the experts agree that the incorrect judgement had been issued. At the time the regenerative receiver was introduced, [[vacuum tube]]s were expensive and consumed lots of power, with the added expense and encumbrance of heavy batteries or AC [[transformer]] and [[rectifier]]. So this design, getting most gain out of one tube, filled the needs of the growing radio community and immediately thrived. Although the superheterodyne receiver is the most common receiver in use today, the regenerative radio made the most out of very few parts. In WW2 the regenerative circuit was used in some early military equipment. A related circuit, the super-regenerative detector, found wide use in WW2 in military [[Secondary surveillance radar|Friend or Foe]] identification equipment and in the top-secret proximity fuse, which had a very important role in winning the war for the allies. === Distance record === The distance record for radio communication was set with a regenerative receiver by [[Russia]]n [[Amateur radio|HAM]] and professional operator Ernst Krenkel during the [[Antipodes|antipode]] - [[antarctic]] [[List of Antarctica expeditions|expedition]] of [[Richard Evelyn Byrd]]. Stalin praised this achievement. === Superheterodyne receiver === In 1906, [[Reginald Fessenden]] had already used a version of the [[heterodyne principle]] for broadcasting. When the parts became easier to obtain, the superheterodyne receiver replaced the regenerative radio for all serious work. Then radio industry matured and prices dropped with increased production. In 1930 the [[superheterodyne]] design began to supplant the regenerative receiver, and after WWII it was almost completely phased out of mass production, remaining only in hobby kits. ==Operating limits== Quality of a receiver is defined by its sensitivity and selectivity. For a single-tank [[Tuned radio frequency receiver|TRF (tuned radio frequency) receiver]] without regenerative feedback, <math>bandwidth = frequency/Q</math>, where Q is tank "quality" defined as <math>Q=Z/R</math>, Z is reactive impedance, R is resistive loss. Signal voltage at tank is antenna voltage multiplied by Q. Positive feedback compensates the energy loss caused by R, so we may express it as bringing in some negative R. Quality with feedback is <math>Qreg = Z/(R-Rneg)</math>. Regeneration rate is <math>M = Qreg/Q = R/(R-Rneg)</math>. Obviously, M depends on stability of amplification and feedback coefficient, because if R-Rneg is set less than Rneg fluctuation, it will easily overstep the oscillation margin. This problem can be partly solved by "grid leak" or any kind of automatic gain control, but the downside of this is surrendering control over receiver to noises and fadings of input signal, which is undesirable. Note that modern semiconductors offer much more stability than vacuum tubes of the 1920s. Actual numbers: To have 3&nbsp;kHz bandwidth at 12&nbsp;MHz ([[short wave]]s travelling all around Earth) we need <math>Q=F/f = 4000</math>. A two-inch coil of thick silvered wire wound on a ceramic core may have Q up to 400, but let's suppose Q = 100. We need M = 40, which is attainable with good stable amplifier even without power stabilizing. ==Super-regenerative receiver== The super-regenerative receiver uses a second lower frequency oscillation (within the same stage or by using a second oscillator stage) to provide single device circuit gains of around one million. This second oscillation periodically interrupts or "quenches" the main RF oscillation, allowing the RF signal to be built up over and over. Strictly speaking, the main RF oscillation still occurs: the detector starts to build up the incoming RF oscillation up to and slightly above oscillation level. But the net result is that most of the time the detector is amplifying the RF signal and is creating a free running RF oscillation in only a small portion of its quenching cycle. A big difference between a straight regen and a super regen is that there is no heterodyne (no squealing interference) as the set is tuned and operated. The super regen uses far fewer components than more complex designs and it is easily possible to build VHF, UHF, and even microwave radio receivers that operate at microwatt power levels. These are ideal for remote sensing applications or where very long battery life is essential. For many years, super regenerative circuits have been used for commercial applications such as garage-door openers, radar detectors, microwatt RF data links, and very low cost walkie talkies. On the other hand, in the normal operating mode a super-regenerative system has an inherent contradiction limiting its use to relatively free and clear bands. Due to [[Nyquist theorem|Nyquist's theorem]] its quenching frequency must be at least twice the signal bandwidth. But quenching with overtones acts further as a [[heterodyne]] receiver mixing additional unneeded signals from those bands into the working frequency. Thus the overall bandwidth of super-regenerator cannot be less than 4 times that of the quench frequency, assuming the quenching oscillator produces an ideal sinewave. However, recent experiments have shown that the self quenched super regenerative circuit may be operated at a level in between the regenerative and super-regenerative states. At these levels, something very interesting happens: A received narrow band FM (RF) signal can be set to heterodyne with the super regen detector's RF oscillations such that sum and difference frequencies are produced. The difference frequency, if close to the detector's quenching oscillation frequency, will lock onto and FM modulate the quench frequency. This produces a large variation in gain which exactly follows the FM modulation of the received signal. The gain variation creates a frequency to amplitude conversion (FM detection) of very high efficiency. To date, this effect has only been studied by electronics experimenters but could eventually lead to very high frequency, ultra low power FM receivers. ==Patents== * Armstrong, E. H., {{US patent|1113149}}, Wireless receiving system, 1914. * Armstrong, E. H., {{US patent|1342885}}, Method of receiving high frequency oscillation, 1922. * Armstrong, E. H., {{US patent|1424065}}, Signalling system, 1922. * Braden, R. A., {{US patent|2211091}}, Superregenerative magnetron receiver, 1940. ==Footnotes== {{reflist}} ==See also== * [[Tuned electrical circuit]] ==External links== {{Commonscat|Radio electronic diagrams|Radio electronic diagrams}} [[Category:Radio electronics]] [[Category:Electronic circuits]] [[da:Superregenerativ modtager]] [[de:Audion]] [[es:Circuito regenerativo]] [[nl:Regeneratieve ontvanger]] [[ru:Регенеративный радиоприёмник]]